| 上海逻迅 | 型号 | N608 |
信息传送内容 | 数据 | 支持网络 | SmartNode |
频段 | 433(MHz) | 发射功率 | 5~40m(W) |
息模式 | PDU | 外行尺寸 | 20×20×4.8(mm) |
SmartNode N608无线模块
无线模块特性:
超低功耗(自动休眠及快速唤醒设计),远距离(2000米),支持路由组网(点对点、点对多点、多点中继),频段434MHz(240~930MHz可设),无线传输速率2.4Kbit/s~128Kbit/s,发射功率7dbm~16dbm(可调),广泛适用于工和民用领域(无线传感器网络;远程抄表系统;温度、湿度、压力监控系统;安防监控系统;无线遥控器;无线数据采集器;智能家居;智能建筑;智能交通;RFID射频识别等)。一、无线模块实物图
超低功耗:侦听电流7uA,休眠电流60nA
功率可调:5mw(7dbm)~400米,40mw(16dbm)~2000米
数据缓冲区:8×256bytes
工作模式(434MHz,64信道):跳频(FHSS),固定频率
数据传输模式:SmartNode协议传输,数据透明传输
数据传输方式:点对点,中继转发(8级组网深度)
接口支持:1路TTL串口、2路I/O,或4路I/O,或4路10位A/D转换
可扩展接口:RS-485,RS-232,USB,CF卡
应用:无线传感器网络;远程抄表系统;温度、湿度、压力监控系统;安防监控系统;无线遥控器;无线数据采集器;无线模块,智能家居;智能建筑;智能交通;RFID射频识别
二、机械尺寸
三、无线模块管脚功能1、TX | 模块UART 发送(TTL 3V) |
2、RX | 模块UART 接收(TTL 3V) |
3、RESET | 模块复位(低电平有效) |
4、I/O2 | 通用输入输出(可扩展) |
5、I/O1 | 通用输入输出(可扩展) |
6、GND | 电源地 |
7、VOUT | 1、当VCC供电时:模块LDO输出3V 200mA 2、1.8V~3.3V供电输入,去除内部LDO电流消耗 |
8、VCC | 电源输入 (3.3V~6V) |
四、无线模块详细参数型号 | 无线模块SmartNode N608 |
电气参数 |
发射功率 | 7dbm~16dbm(可调) |
发射电流 | 24mA(+13dbm);60mA(+16dbm) |
接收电流 | 17mA |
侦听电流 | 7uA (可立即接收数据) |
休眠电流 | 60nA (唤醒时间120uS) |
供电电压 | 1.8V~6V |
射频参数 |
工作频率 | 标准434MHz(240~930MHZ可设) |
信 道 | 64信道 |
工作模式 | 跳频与固定频率(软件配置) |
调试方式 | FSK/GFSK |
无线传输速率 | 2.4 Kbit/s~128 Kbit/s(软件配置) |
接收灵敏度 | -118dbm(2.4Kbit/s) |
通信距离 (空旷) | 400米(7dbm,2.4Kbit/s) 1300米(13dbm,2.4Kbit/s) 2000米(16dbm,2.4Kbit/s) |
模块ID | Modem ID 32bit |
厂家识别码 | PID 16bit |
用户识别码 | UID 16bit |
通讯接口 | TTL串口8N1 |
串口速率 (Kbit/s) | 1.2,2.4,4.8,9.6,14.4,19.2,38.4 (可软件配置,出厂默认9.6Kbit/s) |
通讯协议 | SmartNode协议,支持路由、组网 |
数据传输模式 | SmartNode 协议传输、透明传输 |
天线接口 | IPEX,IPEX to SMA,内置天线 |
其他参数 |
工作温度 | -40℃~+85℃ |
尺寸 | 20mm×20mm×4.8mm |
无线模块注意事项:
1、 为了决定是否要安装无线模块或在里安装无线模块,在安装无线模块之前,应该分析一下无线模块周围的环境。
2、 无线模块应该尽可能地被放置在高些及有空间的地方,这样无线模块之间的连接会更强更远。建议离地1.5 米以上,效果更佳。
3、 应避免在无线模块周围放置金属物体,以免无线被屏蔽减弱。
4、 无线模块的电子会来源于以下多种物体,所以应该加以避免:
-发动机
-高电流设备
-继电器
-变压器
-等等
5、 振动或打击也可能会是的来源。所以为了使无线模块的性能稳定可靠,建议无线模块的放置部位应尽可能静止。
6、 无线模块外壳上的标签有 ID等重要信息,请务必妥善管理。
7、 请不要随意拆卸无线模块,造成一切后果有用户自行承担。
销售与技术支持
上海逻迅信息科技有限公司
电 话: 086-021-58521893
086-021-52726083
传 真: 086-021-60919295
地 址: 上海 上海市浦东新区
张杨路 1589 号1 号楼1304 室
邮 编: 200135
网 址:
上海逻迅注于无线模块,无线收发模块,无线数传模块,无线组网模块,无线传感器,无线传感网络。
Wireless module Note:
1, in order to decide whether to install the wireless module or where to install the wireless module, wireless module is installed, you should analyze the environment around the wireless module.
2, the wireless module as sible should be placed higher and there is room in the place, so that the connection between the wireless module will be further enhanced.Suggested more than 1.5 meters from the ground, the better.
3, should be avoided in the wireless module is placed around metal objects, so as not to shield the wireless signal is weakened.
4, the wireless module of electronic interference from the following variety of objects, so it should be avoided:
- Engine
- High current devices
- Relay
- Tranormers
- Etc.
5, vibration or combat may also be sources of interference.Therefore, in order to make stable and reliable performance of the wireless module, it is recommended to place the wireless module parts should be as static.
6, the wireless module with ID label on the cover and other important information, be sure to properly manage.
7, do not disassemble the wireless module, causing the user to bear all the consequences.
Sales and Technical Support
Logic Xun Information Technology Co., Ltd. Shanghai
Tel: 086-021-58521893
086-021-52726083
Fax: 086-021-60919295
Address: Shanghai Pudong New Area, Shanghai, China
Zhangyang 1589, Building 1, Room 1304
Post Code: 200135
Website:
Shanghai logic rapidly focus on wireless modules, wireless transceiver module, wireless module, wireless networking module, wireless sensors, wireless sensor networks.